LSR Wireless RF Design Blog

How will the new FCC 14-208 changes impact testing for wireless products?

Posted by Tom Smith on Mon, Jan 26, 2015 @ 16:01 PM

On December 30, 2014, the FCC released a report, FCC 14-208 (ET Docket No. 13-44), which includes a number of significant changes to FCC Parts 0, 1, 2, and 15 regarding authorization of RF equipment, as well as FCC Part 68 regarding approval of terminal equipment by the Telecommunication Certification Bodies (TCB).   Scheduled to go in effect on January 30, 2015 (30 days after release of the report), there are a number of critical changes that manufacturers of wireless products need to be aware of.  We will attempt to walk you through the key changes, and explain what impact they may have for your organization.

FCC will require test labs to be accredited in order to perform FCC Certification or DoC Testing               

Historically, test data for FCC Certification or DoC applications could be submitted by labs that were either accredited, or listed under FCC Part 2.948.  Accredited laboratories, such as LSR’s EMC facilities, undergo a stringent accreditation process to the requirements of ISO 17025.  Accredited labs must also complete a re-assessment every 2 years to retain their accreditation.  Moving forward the FCC and TCB’s will NOT be accepting test data from listed laboratories for FCC Certifications or DoC reports.

All labs that are currently not accredited will have a 1 year grace period to achieve accreditation.  The FCC will allow data from listed labs for a grace period of 15 months.  In addition to the rigorous accreditation process, this may require additional investments in site capabilities, lab equipment, and personnel in order to meet the standards.  Therefore, it is possible that a number of listed laboratories may choose not to pursue accreditation. If you are unsure if the lab you have historically used for your FCC testing is currently accredited, you can determine that from the FCC’s website, here

Where this change is likely to have its strongest impact is on the use of international testing laboratories.  The same accreditation requirements will apply for international laboratories. Previously, many of the laboratories in international countries were not on the FCC’s list of accredited laboratories. For example, in some places like China, none of the laboratories are on the FCC’s accredited laboratories list.  In the future, unless the country the lab is located in has an MRA (Mutual Recognition Agreement) in place with the FCC, such as EU, Japan and a few other countries, or has laboratories recognized as accredited by the FCC commission, they will no longer be able to provide test data that will be accepted for Certifications or DoC’s.   For a complete list of countries with an MRA in place with the FCC, click here

It’s important to note that this change does not apply for FCC Verification testing, which is the level of testing required for electric products that do not intentionally transmit wireless data or feature the FCC logo on its product packaging.  In those instances, listed labs can continue to provide the verification testing. 

FCC is giving TCB’s authority to process and grant all applications for FCC certification

For any product containing a wireless radio, FCC certification is required for marketing of the product in the US.  For quite some time, TCB’s have done the lion’s share of processing and granting applications for FCC certification, with just a small % being handled by the FCC directly.  This was especially the case when the product was utilizing an emerging technology.  Moving forward, all applications will be handled by TCBs.  For emerging technologies, a new “Pre-Grant Approval Process” has been defined for the TCBs to follow. 

What do these changes mean for LSR customers? 

These changes will have minimal impact for customers of LSR’s EMC Testing division, as LSR has been ISO/IEC 17025 accredited since 1997, and already has an established and strong relationships with its TCB. 

LSR is focused on providing the highest level of support and expertise for FCC testing, and is committed to remaining your trusted partner for these services moving forward amidst these changes.   Should you have questions about current or future projects, please reach out to an LSR account manager to discuss further.

Topics: Certification, FCC Filing, DoC, EMC Testing, Wireless Products, TCB, Compliance

Selling a 5 GHz-Based Wireless Product in Europe? Here's What You Need to Know About the New ETSI EN 301 893 v1.7.1

Posted by Ryan Urness on Mon, Nov 17, 2014 @ 10:11 AM

You’ve likely heard by now that the European Telecommunications Standards Institute (ETSI) will be implementing a new set of compliance standards for 2.4 GHz wireless products, effective January 1, 2015.  You may not be aware, however, that there will also be changes that impact products using the 5 GHz ISM band, due to the release of ETSI 301 893 v1.7.1

Let’s take a minute to help ensure you have a plan for handling these additional upcoming CE Mark changes:

What products fall under the purview of the new EN 301 893 v1.7.1?

The ETSI EN 301 893 standard addresses any broadband radio access networks (BRAN) and 5 GHz radio local area networks (RLAN) products sold into Europe that utilize the 5 GHz ISM band. Examples would include products that incorporate Wi-Fi 802.11 a/n communication protocols.

Can I simply update the test data that was acquired back when my product was certified to meet EN 301 893 v1.6.1?

In some cases, yes. The most significant changes in the standard are not simply new limits, but rather changes to the actual test procedures and/or additional tests. Therefore, new test data may need to be taken to confirm compliance with the v1.7.1 standards.  Consulting with a testing expert like LSR is the best way to determine whether additional test data is needed.

What Lab capabilities are needed to be able to successfully test for compliance to these new standards?

The new v1.7.1 standards for 5 GHz have redefined many of the test procedures and types of measurements required, which also raises the bar on the capabilities and equipment a testing facility must have in order to complete this certification. Specialized test equipment required includes:

  • a Power Meter with ability to sample at a rate of 1 Msamples/sec
  • a Signal Generator that can provide a noise profile for testing Adaptivity

How soon do I need to begin the process of certification for v1.7.1?

As always, the sooner the better, to provide you time to address any design changes that may be needed should testing determine that the standards cannot be successfully met. The complexity of the testing and the number of measurements required could result in a week or longer of testing time to complete.

Partnering with LSR for EN 301 893 v1.7.1 Certification provides:

  • An evaluation of the standards and how it applies to your product, so a detailed, custom statement of work can be provided
  • The support of a team experienced with testing to these new standards, as LSR has been re-certifying all of its own Wi-Fi modules.
  • Knowledgeable professionals working with you to troubleshoot and identify the source of any non-compliance to these new standards
  • The necessary testing equipment and facilities to complete these tests in an accurate and timely manner
  • All the needed documentation to update your DoC before January 1, 2015

LSR has the necessary equipment, the knowledge of the new v1.7.1 standard, and the experience in testing that you’re looking for. Let us help you set a strategy to meet these new changes by contacting us today!

Topics: Certification, EMC Testing, Wireless Products, ETSI

CE Marking: Know your standards

Posted by Ryan Urness on Wed, Sep 10, 2014 @ 06:09 AM

LSR’s Test Services Division commonly answers questions regarding selecting the appropriate standards for demonstrating conformity to the essential requirements of the EC Directives when CE Marking a product.  So, we thought we’d put together a quick blog to identify some terminology and provide a basic explanation to the hierarchy of requirements. For these examples, we’ll use the EMC Directive 2004/108/EC, but the steps are similar regardless.

First, It is important to understand CE marking and how it relates to conformity.  Directive 93/68/EEC establishes the scope, structure, and application for CE Marking, which is the official terminology as specified by the EU (in lieu of the term “CE Mark”); and signifies Declaration of Conformity by the manufacturer.  By CE Marking a product, the manufacturer is declaring conformity with the Essential Requirements of all relevant European health, safety, and environmental protection legislation; as outlined in the EC Directives; however, it is up to the manufacturer to determine which Directives are applicable.  The terminology used for this is Self-certification and is part of the New Approach method of standardization.

Currently, there are 32 countries that participate in the New Approach, perform market surveillance, and require CE marking.  Though manufacturers may receive assistance when determining which directives (and subsequent standards) are best suited for a conformity assessment, it is ultimately the responsibility of the manufacturer to construct the Declaration of Conformity and provide a subsequent record supporting these declarations, if requested by market surveillance authorities.  Consequently, it is important that once a directive is determined as applicable to the product being considered for conformity assessment (such as the EMC Directive, for example, in this blog); the essential requirements can then be identified.

Second, let’s review a basic understanding of the classifications and hierarchy of requirements.  Article 6 of 2004/108/EC paragraph 2 identifies using the Official Journal of the European Union (OJEU) to identify all relevant harmonized standards, which upon application would satisfy the essential requirements of Annex 1 of the EMC Directive.  The EC Directives comprise the legislative requirements that conformity must be declared to, and the OJEU is a listing of harmonized standards that’s accepted by the member states as satisfying all of these essential requirements.

These Harmonized Standards are Product, Product Family, or Generic; and provide the Technical Specifications relevant to the device being tested.  Product Standards are specific to the product being tested, think: electrocardiographs; whereas Product Family Standards are specific to the type or class of product, think: medical electrical equipment; and Generic Standards are based on the applicable product environments (such as Residential or Industrial) rather than product type, and are to be utilized when no applicable product family standards are available. 

Third, Basic Standards provide test methodology and arrangement; they don’t specify requirements.  Because there are no technical requirements in a basic standard, they do not appear in the OJEU.  As a result, it’s important to note that making declarations of conformity to Basic standards are unnecessary.

So, the legislative requisites are contained in the EC Directives in the form of essential requirements, and reference a list of harmonized product, product family, and generic standards that provide recognized technical specifications used for demonstrating conformity in the 32 member-states of the EU; some technical specification will contain specific methodologies, or they may reference basic standards which outline the test arrangement and general methods to be used.  The image below is a visual outline of this hierarchy:

CE Marking
This provides a visual outline of the hierarchy of Directives

It is also important to note that compliance to the harmonized standards is not compulsory.  There are alternative for demonstrating compliance beyond using the harmonized standards contained in the OJEU.  This process, for example for the EMC Directive 2004/108/EC it’s outlined in Annex III, consists of constructing technical documentation submitted to a Notified Body (as defined in Article 12 of 2004/108/EC) for a conformity assessment.

In closing, proper conformity assessment for a product according to the requirements put forth by the European Union and member states would include identifying all of the applicable directives outlined in the New Approach.  As an example, when applicable, the EMC Directive 2004/108/EC requires that the essential requirements of Annex 1 are observed: either through compliance to the generic, product family, or product specific standards specified in the Official Journal of the European Union, or via an assessment of a manufacturer’s technical file by a notified body which demonstrates an equivalency.  In the event that the harmonized standards of the OJEU are utilized for the Declaration of Conformity, member states do agree to a presumption of compliance.

Understanding the different types of standards and relationships between them is an essential component in understanding which requirements will be applicable for conformity to the EMC Directive, and only upon demonstrating compliance with ALL the applicable directives of the New Approach can a product be subject to CE marking.

LSR has an accredited test facility, and has provided guidance in design services and European conformity assessment for over 30 years.  LSR is also recognized as a Conformity Assessment Body, and as such can provide Notified Body services to any of our customers for both the EMC (2004/108/EC) and R&TTE (1995/5/EC) Directives.

Topics: Certification, CE Mark, EMC Directive, Compliance

The 4th Edition of IEC 60601-1-2 and How it will Affect You!

Posted by Unwired LS Research on Wed, May 28, 2014 @ 10:05 AM

About the Author: Shane Rismeyer is an EMC Engineer for LSR’s Compliance Division.  He received his BS in Biomedical Engineering from MSOE, is a member of IEEE, and is involved with the Milwaukee Chapter of the EMC Society.  You may contact Shane via email at

With the release of a new medical standard (as with any) there comes a certain amount of apprehension and concern about how current and future products will fit into a new testing scheme. In the medical field this is especially true, as there are additional factors that come into play when seeking approval, as compared to typical consumer products.  The fourth edition of IEC 60601-1-2 brings with it a revamped product classification system for both emissions and immunity.

Gone is the old system based on whether or not a product is life supporting, replaced by a classification system based on intended use environment. The new organizational model is better suited for the diverse range of products found in today’s medical field. In order to reduce the susceptibility of these products the fourth edition has increased, added to or changed many of the stress levels for the immunity tests. One of the major focuses addresses the increased proliferation of wireless devices across multiple frequency bands. With these changes in the immunity suite, this will result in a rather distinct difference in tests when compared to the third edition. This is an important point to remember when considering upcoming compliance testing.

At this post, the fourth edition is still several years away from being requisite, and not published in the Official Journal associated with the Medical Directive. For further information regarding these changes or questions regarding the approvals process, you may contact LSR through our website at, connect with us on LinkedIn, or find our latest news and information on Twitter by following @lsresearch.




Topics: Certification, Emissions Testing, Compliance, Medical Standards

FCC Certification: FCC Proposes Major Changes to Certification Rules

Posted by Ryan Urness on Mon, Mar 18, 2013 @ 13:03 PM

dreamstime xs 8890106On February 15, 2013, the FCC released a Notice of Proposed Rulemaking to amend FCC Parts 0, 1, 2, 15, and 68.  The PDF document can be found here (ET Docket No. 13-44  RM-11652).

The changes proposed by the FCC will affect the TCB Program, Test Laboratory Accreditation and Validation, and recognized Measurement Procedures; and have an implementation transition period of one year after publication of the rules in the Federal Register.


The TCB Program:

The telecommunications certification body (TCB) program, which has been implemented since June of 2000, is well established; and the FCC is proposing to no longer directly issue any grants of equipment authorization for wireless products or modules, but instead allow TCBs to authorize all wireless products subject to certification.  This would include eliminating the current KDB TCB Exclusion List of device types which still require the Commission for certification, but also implementing a "pre-approval" process for specific product types which would require TCB to receive the Commissions concurrence prior to granting an equipment authorization.  This transfers the authority for granting certification to the TCB, while still allowing the Commission oversight and control of these special product types; at least until such time that the Commission determines oversight is no longer requisite.  

In addition, the FCC is proposing changes to the post-market surveillance rules to clarify the authority of TCBs when requesting samples from grantees, and procedures for when the Commission requests a TCB perform surveillance on a specific device, as well as procedures in the event a non-compliance is discovered.

The Commission is also seeking input regarding logistics, counterbalancing influences, and minimizing the expense of these post market surveillance efforts.  Suggestions such as sample request methods that limit solicitation duplication, cross-checking efforts amongst TCBs, and how the burden of expense for these efforts are distributed are currently under proposal.

A clarification of the role NIST will have in the designation of domestic TCBs, along with clarification of the process with which a laboratory must follow to demonstrate competence as a TCB.  With the proposal of added authority for all equipment authorization for TCBs, the Commission is also proposing new corrective programs when deficiencies are discovered with a TCB, and under current rules there is no recourse other than withdrawal of the TCBs designation or recognition.  These efforts would be designed specifically for performance issues that the Commissions recognizes can be resolved with simple corrective actions by the TCB.  

 Test Laboratory Accreditation and Verification:

One of the most significant changes being proposed has to do with a change to the Commission's requirements for Test Laboratories, the acceptance of data based upon accreditation, and the requirements for measurement sites.  

Currently there are three authorization procedures: Certification, Declaration of Conformity (DoC), and Verification.  Certification is a grant of equipment authorization issued by the Commission or TCB based on the submittal of an application and test data; a Declaration of Conformity is a statement of conformance to the requirements with the appropriate technical standards but isn't requisite for a grant of equipment authorization from the Commission or TCBs, just a statement supplied with the product; and a verification requires no application for a grant of equipment authorization, nor a statement of compliance, just performance of measurements which ensure the equipment complies with appropriate technical standards.   

Under current Commission rules, only DoC procedures requires laboratory accreditation to the requirements of ISO/IEC 17025; however, under this proposal, accreditation will be required for laboratories performing certification as well, with the most significant effect being that any testing performed in countries without a US MRA may not be accepted for Part 15 or Part 18 certification.

Additionally, the proposal will update the test site validation requirements to those specified in ANSI C63.4-2009 for emissions below 1GHz, and the Site VSWR requirements specified in CISPR 16-1-4 for emissions in the range of 1GHz to 40GHz.

Measurement Procedures:

The Commission is also proposing To incorporate ANSI C63.4-2009 and ANSI C63.10-2009 for determining the compliance of unintentional and intentional radiators respectively.  However, the Commission will not acknowledge the use of rod antennas below 30MHz, artificial hand for handhold devices, or absorber clamps for radio noise power measurements due to insufficient evidence that they produce accurate, repeatable measurements.  Additionally, it will not observe relaxation of limits for emissions of a transient nature resulting from findings which demonstrate that brief durations in emissions still produce nuisance interference. 

As of the publishing of this blog, the FCC will continue to review comments regarding the proposed rulemaking for another 4-5 weeks, with responses to comments following 30 days later.

Topics: Certification, FCC, FCC Filing, DoC, Wireless Products, TCB

Tell Us! Is your Intentional Radiator Design a Success or Failure?

Posted by Robert Buczkiewicz on Fri, Feb 22, 2013 @ 12:02 PM

describe the imageOver the years I've presented at several wireless seminars. My favorite question to ask is always, 'How many of you have submitted your designs for FCC testing?' and most hands fly up. I then follow up with another question, 'How many of you have passed compliance on your first try?' and unfortunatley, most hands go down just as fast.

The Federal Code Of Regulation (CFR) FCC Part 15 is a common testing standard for most electronic equipment. FCC Part 15 covers the regulations under which an intentional, unintentional, or incidental radiator that can be operated without an individual license. FCC Part 15 covers as well the technical specifications, administrative requirements and other conditions relating to the marketing of FCC Part 15 devices. Depending on the type of the equipment, verification, declaration of conformity, or certification is the process for FCC Part 15 compliance.

FCC Part 15 Subpart C is for intentional radiators. An Intentional radiator is any device that is designed to produce a radio signal on purpose. The FCC has made provisions for unlicensed transmitters throughout the radio spectrum. The various types of intentional radiators covered by Subpart C include cordless telephones, remote control and alarm transmitters and spread-spectrum systems for wideband data transmission which include WiFi, Bluetooth and ZigBee devices. The FCC Part 15 Subpart C rules for operation of radio transmitters for the most part are very detailed regarding fundamental field strength, power and/or power density, frequency accuracy, and permitted harmonic and spurious emissions.

With the advent of single chip or system on chip (SoC) transceivers it has become much easier and cost effective to add a low power wireless device to any product.  Most semiconductor manufacturers such as TI, Semtech, SiLabs and Analog Devices provide full featured reference designs and in some case even the CAD files that lower the overall development risk and time to market.  Regardless of the wireless technology platform, all products that include an integrated radio are subject to intentional radiator testing.  And even if a reference design is carefully replicated in the end product, there is a chance that the final design may fail one or more portions of the compliance testing. Antennas, cables, RF shields, power supplies, passive component selection, PCB trace routing and stack may all influence radiated emissions.

I’d like to pose the following questions to learn about your success and/or failures related to FCC testing:

  1. How many PCB spins are typically required to achieve compliance?

  2. How many visits to the compliance lab are usually required for success?

  3. How do you prepare to assure you have the greatest chance of success?

  4. Do you prescan the device early on in the development phase or just wait and test when the design is completed?

  5. What common, reoccurring failures do you observe? Transmitter harmonics, emissions off the antenna, emissions off the PCB?

  6. What tricks do you use to isolate or fix problems?

  7. How much does your PCB layout impact the emissions?

  8. How does adding a  power amplifier (100 mW, 500 mW) to the transmitter impact your chances of compliance success?

Topics: Certification, FCC, Antenna Design, EMC Testing, Compliance, SoC

Certification, EMC Testing, and Standards Update

Posted by Ryan Urness on Wed, Jan 30, 2013 @ 13:01 PM

certification_standardsNorth America (FCC, Industry Canada): 

The FCC Office of Engineering and Technology (OET) laboratory division released an update to KDB Publication Number 447498 on January 29th, 2013; which updates the RF Exposure requirements for Mobile and Portable devices, located in Title 47 CFR Part 1 Section 1.1307, Part 2 Section 2.1091, and Part 2 Section 2.1093.  The KDB Publication can be found here.

The attachments to the KDB 447498 D01, and 447498 D02 are the general RF Exposure Guidance document and the SAR procedures for a dongle transmitter respectively.  Additional attention should be observed for equipment types outlined in KDB 628591, the exclusion list for telecommunication certification bodies (TCBs).  The exclusions of evaluation for these equipment types includes specific absorption rates (SAR) RF exposure evaluations. The TCB Exclusion List KDB Publication can be found here

Industry Canada released Notice 2012-DRS1203 in response to the revision of the FCC RF Exposure KDB procedure, and the applicability of those requirements to Industry Canada.  In addition, there is further guidance on the applicability of other procedures when seeking certification for the Canadian market.  A copy of the Notice from the Certification and Engineering Bureau can be found here.

The Ministry of Economy (Secretaria de Economia) of Mexico published new requirements for equipment related to telecommunications standards NOM-121-STC1-2009 and NOM-151-SCT1-1999; or specifically equipment utilizing Spread Spectrum techniques such as Bluetooth modules, Bluetooth Low Energy, WiFi modules (802.11 b/g/n), and Zigbee products.

The following agreements were made as of January 11, 2013:  

  1. All imported equipment related to NOM-121 is now required to present verification of compliance at customs by either presenting a Certificate of Compliance issued by an accredited certification body of Mexico such as NYCE, or a Homologation Certificate issued from COFETEL.

  2. NYCE has pledged that the certification process shall not exceed a period of 10 days from submission of the application, and will send the issued certificates to the Ministry of Economy to be entered into the system, which will prevent delays when customs is reviewing compliance.

  3. The name of the importer does not need to match the name of the recipient of the certification (with either case, NYCE or COFETEL)

  4. Equipment with COFETEL Homologation Certifications have additional requisites specific to labeling



The European Union Association of Notified Bodies released a reference document reviewing the EMC Testing requirements for products that integrate radio modules.  LSR has written several articles regarding this process, such has our September 25, 2012 Blog on what to do after you've integrated a Wifi module into your product, and our news article on integrating radio modules for Europe published July 2, 2012

The EUANB Reference document points out that the relevant requirements against the various applicable directives of non-radio based equipement may not harmonize to the requirements of the R&TTE directive placed upon a radio based module.  

Prior to leveraging a modular device's conformity document to demonstrate compliance once itegrated into a product, an assessment of the test methods and requrements must be performed against the outlined product requirements and the performed modular radio testing. Instances which the conformity requirements of the product and module are not harmonized, the more stringent requirements shall take precedence, and the equipement shall be monitored for appropriate operation.

Topics: Certification, FCC, FCC Filing, Module, EMC Testing, Electromagnetic Compatibility, WiFi Module, R&TTE Directive

Dont Forget: The 5 Basics of RF Design

Posted by Jen Sarto on Thu, Jan 10, 2013 @ 09:01 AM

describe the imageIf it's time to go wireless, don't forget the basics of RF Design. You may be excited about your new wireless project: innovative design, environmentally friendly, consumer demand, and the list could go on. Whether your budget is substantial or minimal, it is important to keep in mind the following questions in order for your project to go ahead without a hitch. 


1. Where will your product be based? U.S., Asia, Europe, Canada?

Knowing where the product will be sold will help you during the design and certification process. Different regulatory bodies control frequency spectrum, allowable output power, and testing requirements. For instance, in the US (per FCC regulations), you can operate a product in the 902-918 MHz ISM band, while in Europe (per ETSI regulations), the same band is not allowed, however the Short Range Device (SRD) band of 863 to 870 MHz is license free and may provide similar performance. The 2.4 GHz ISM band is the most widely used frequency as it is a license free band in more than 95% of the world. When designing your product, you must understand if you are designing per FCC rules (US), ETSI (Europe), C-Tick (Australia), or IC (Industry Canada). For more information on the administrative preparation needed for testing watch our video.

2. Who will be using your product and how will it be used?

Understanding how the product will be used will affect the type of radio selection and antenna design or selection. For instance, if it is a handheld product, you may want to consider a radio that does not operate in the 2.4 GHz band, for superior range performance, as the human body radially absorbs RF energy at 2.4 GHz. Additionally, you will want to optimize the antenna for use on the human body and consider if SAR (Specific Absorption Rate) or RF exposure testing is required. 

3. How large is the production of your product, and within what time frame is your product desired?

The FCC allows for modular approval which can be very advantageous to OEM's who are using the same radio design across multiple sku's or platforms. By meeting the FCC's 8 Key Requirements for Module Approval, you can certify the module once and reference the FCC ID number across all products. This can drastically save you time and money.

4. Does your product need to be plugged-in, use solar power, or operate on batteries?

Understanding the power supply and operating conditions is critical when selecting a radio. Most popular radio technologies are relatively lower power, however there are significant differences between radios designed for ultra-low power sensor applications vs. radios designed for sending pictures or streaming videos.

5. What is your time frame and budget?

When it comes to wireless design and development, you have multiple options on how to make your product wireless. Certified off-the-shelf rf modules are arguably the fastest and easiest way to market. Discrete design, another option, may provide you with the most aggressive product costs and optimized design for your application, however this type of implementation involves weeks to months of engineering efforts, plus certification costs and time. 

Of course, all these factors have an impact on cost and risk. With a little due diligence up front, you can avoid many pitfalls along the way. Take a time to make sure all interested parties are in agreement with the work ahead. 

Topics: Certification, FCC, Antenna Design, Module, RF Design, Wireless Products

FCC Testing & Filing: Administrative Preparation

Posted by Ryan Urness on Thu, Jan 03, 2013 @ 15:01 PM

There are numerous steps to take when filing your product with the FCC. Administrative action can be taken before the FCC Testing is started in order to reduce the document filing and submittal period. The video below reviews the administrative preparations needed prior to starting a certification program, including:


 Authorized Signatory
 Obtain FRN
 Purchase Grantee Code
 Generate FCC ID#
 Product Paperwork 


Topics: Certification, FCC, FCC Filing, EMC Testing

FCC Certification: OET KDB Updates

Posted by Ryan Urness on Fri, Dec 07, 2012 @ 15:12 PM

usa flag_chipThe FCC Office of Engineering and Technology (OET) laboratory division periodically releases lists of updates to the OET Knowledge Database (KDB); the following are some of the latest KDB updates, with a brief review of the subject and content of the KDB publications. 

The OET KDB is a useful resource which is used as a reference and research tool, and serves as a repository for answers to both common, and not-so-common, questions regarding the the complex process of Equipment Authorization and FCC Certification.

The OET KDB search can be visited at:; which also has a link to an RSS Feed for those looking to keep abreast of the most recent changes. 


KDB number 178919 - Permissive Change Policy

  • This publication provides as attachment, 178919 D01, which outlines the general policy and specifications for a permissive change to a Grant of Equipment Authorization.  Categories for the permissive changes and policies addressed in this document include: antenna design changes, PCB or hardware changes, changes to the enclosure, software changes, and other basic miscellaneous revisions.  Permissive changes are classified as Class I or Class II; Class I permissive changes require re-evaluation upon the type change, but not re-submittal for a new Grant of Equipment Authorization.  A Class II permissive change requires submittal for an updated Grant of Equipment Authorization for equipment operating under an existing FCC ID number.  The policy was updated on 10/24/12 to allow TCBs to approve third part software upgrades under the "Permit but Ask" policy of the FCC.  Additionally, RF exposure considerations have been updated to reference the published RF Exposure KDB procedures.

KDB number 852134 - Authorized Individual Policy (Form 731)

  • This KDB document reviews the role of an authorized agent of form 731, and the guidelines which are to be followed when during the filing of an Application for Equipment Authorization, or amending an existing Grant of Equipment Authorization.  Attachment D01 of this publication was last updated on 12/3/12; with an adjustment to the procedure for submitting a request for the Grantee Code number if an applicant is not the authorized contact in the Grantee Code Database.

KDB number 204515 - Grantee Code

  • This publication outlines the guidelines for acquiring a Grantee Code, modifying the information in the Grantee Code Database, and transferring control of a Grantee Code.  The guide was published on 12/3/12 in response to a submitted KDB inquiry.

KDB number 726920 - Confidentiality

  • This publication reviews confidentiality of information submitted during the Equipment Authorization.  There are four attachments associated with this publication. 726920 D01 is a table outlining the applicability of confidentiality to various exhibits submitted during an Equipment Authorization and whether long-term or short-term confidentiality is available.  726920 D02 details the procedure for requesting confidentiality during an Application for Equipment Authorization. 726920 D03 provides specific details when the application is processed by the FCC, and 726920 D04 provides details when the application is processed by a TCB.  The KDB publication date was 12/3/12

Radio Service:

KDB number 558074 - DTS Measurement Guidance

  • This publication's attachment, 558074 D01, provides guidance on the procedures for compliance measurements on Digital Transmission Systems operating under Title 47 CFR Part 15, Subpart C, section 15.247. The guidance was updated as clarification to existing procedures and to expand measurement options to accommodate contemporary digital modulation schemes.  The guidance document supersedes any previous revisions of this publication, but does not invalidate the measurement methodology document ANSI C63.10.  Publication date was 10/4/12.

KDB number 789033 - UNII Test Procedures

  • This publication outlines the general test procedures and guidance for testing UNII type devices.  The attachment, 789033 D01, replaces and supersedes guidance in Public Notice DA 02-2138 from August 2002; and is the general test procedures for testing UNII devices to Title 47 CFR Part 15 Subpart E section 15.407.  The procedures for evaluating DFS functionality and MIMO devices are not applicable to this guidance document, and can be found in FCC order, ET Docket No.03-122 and KDB Publication 662911 respectively.  789033 D01 was revised on 9/26/12 with clarifications to duty cycle and power spectral density; a modification allowing testing single channels for each modulation mode for overall test time reduction purposes; an addition allowing 15.209 limits to satisfy peak emission limits under certain circumstances, and a replacement guidance procedure for array gain for spurious emissions (reference KDB Pub. 662911).

RF Exposure / SAR:KDB number 447498 - Mobile and Portable RF Exposure

  • This publication outlines the Equipment Authorization requirements for RF Exposure on devices classified as Mobile or Portable.  The publication has three attachments.  447498 D01 provides guidance for general RF Exposure; 447498 D02 provides procedures and policies for Mobile and Portable RF Exposure; and 447498 D03 provides SAR procedures for USB Dongle transmitters.  KDB publication 447498 was updated on 10/24/12 in response to a direct KDB inquiry.

KDB number 690783 - Guidance for TCBs listing SAR on Grants of Equipment Authorization. 

  • This publication was updated on 10/24/12 to reflect various changes made to RF Exposure guidance.

KDB number 865664 - RF Exposure on GHz devices

  • This publication provides a change notice that the 2006 FCC SAR 3 to 6 GHz Rev document has been replaced by 865664 D01, SAR measurement 100MHz to 6GHz.  The publication date was 10/24/12.

Topics: Certification, FCC, DoC, Antenna Design, Module